Design:
Tworzenie stron Warszawa

Tworzenie stron

Poly

POLYSUPERPAC.com is excited to announce new life for old Polys... The original ‘A’ engine, (aka Poly), was introduced in 1956 as a significant replacement for the Hemi of that era... Much more economical to produce but still having opposing valve placement ala the Hemi, it was a very strong performer from idle to 5000rpm, in contrast to the Hemi which performed well from 3000 to 7000+. The factory four barrel and two four barrel versions were the HOT setup and performed very well from idle thru 5500rpm. Weiand produced the aluminum single four #7503, aluminum three deuce WPD3D, and the aluminum dual quad WPD4D, all single plane divided plenum intakes that performed well through 6500rpm although a bit “soft” on throttle response under 3000rpm, without the requisite “hot-rod” mods of lower rear gears and high-stall convertors or four speeds.

In 1956 Edelbrock produced a three deuce P600 dual plane manifold with a three-bolt carb pad for the Stromberg 97’s and Holley 94 style 2bbl. carburetors of the day and a later four-bolt carb pad in the sixties to accommodate the popular Rochester style 2bbl. carburetors. All these manifolds worked well during that era and are still good performers today, (if and when you can find them), even on Stroked Poly engines. However, modern technology allows us to build a “better mousetrap” for the Poly – our WOLF in sheep’s clothing.

 A consortium of Chrysler engines specialists and credentialed engineers (Gary Pavlovich, Gary Stauffer, Roland Osborne & Martin Ahlgrim), met recently with foundries and patternmakers in California to begin production of a series of Gen II Poly manifolds which will work well from idle to 6500rpm in “as cast” form for all 277-301-303-313-318-326 Plymouth and Dodge Poly engines as well as BUILT Stroker Polys. Using the dual plane air-gap technology of the modern Hot Heads HEMI intake manifold, graciously loaned by Bob Walker of “Hot Heads” in Lowgap, NC, and using Hot Heads’ original patternmaker and foundry, Javier Vasquez/FoundryWorks, POLY SUPER-PAC now has this ‘hot-ticket’ available to bolt on and go spank some unsuspecting Chevys, Ford and Hemis.

Be the first on your block to slay some giants with your Poly... Coupled with an appropriate carb for the engine, it will rip your head off from idle all the way thru 6 grand!!! PolySuperPac.com also has a very generous warehouse and jobber program available…

Also of note are the new PolyPac finned aluminum valve covers in four popular styles, TTI headers, bolt on electronic ignition kits, Milodon oiling systems, transmission hookups and all the heretofore hard to find pieces common to the Poly that no one knew where to get ‘n’ go…

Display: List / Grid
Show:
Sort By:
STREETFIGHTER Poly Econo Stroker Kit
My personal favorite kit— we've named the STREETFIGHTER... (and I've spent looooon..
$1,098.00
CPSS-X Gen 1 Kit
Listen up SportsFans… CPPA hits it out of the park AGAIN!!!  Seen here is the culm..
$1,495.00
ECONO 330/333 Package 9:1CR 340HP
Don’t pull that perfectly good Poly and make yourself crazy trying to install a Big Block that wa..
$350.00
ECONO 360 Package 9:1CR 375HP
Don’t pull that perfectly good Poly and make yourself crazy trying to install a Big Block that wa..
$350.00
ECONO 402 Package10:1CR 425HP
Don’t pull that perfectly good Poly and make yourself crazy trying to install a Big Block that wa..
$350.00
Four Barrel ‘Wind Tunnel’ Dual Plane Manifold
Another FIRST from Chrysler Power/CPPA... Known for 40 years as the innovator that gives Mop..
$615.00
Poly Ignition Kit
MP Electronic Kit For All Poly Engines — 277-318-326…1956-1966 ..
$249.00
Poly Intake Gasket Set
..
$39.00
Bolt Set Includes Carb Studs. ..
$59.00
Poly Power Valve Cover Set
The three bolt valve cover works fine on two bolt engines... Options are to drill and tap th..
$399.00
Poly Stroker Kit
Stroker Kit For All Poly Engines — 392-413-426-etc crank, rods, pistons…1956-1966 ..
$1,795.00
Solid and Hyd. Camshafts
Camshafts For All Poly Engines — 277-318-326…1956-1966 256/.435”(208@.050”)Idle to 5000 ..
$295.00
Powered By OpenCart and OC2PS
Chrysler Power Webstore © 2017